m0n0wall (monowall) 800MHz Router / Firewall - VPN,VLAN For Sale

These small and silent embedded PCs come with m0n0wall version 1.33 (or later) pre-installed on the ATA Disk-On-Module (Flash / SSD). They were built from refurbished thin client computers. They are fully tested and are guaranteed to be in full working condition. They come with everything needed to be up and running as a m0n0wall Firewall/Router (including ac adapter)

You will need to setup the initial IP address by hooking up a keyboard and monitor. After that you can configure everything remotely using the included web administration utility. (for samples of configuration see the m0n0wall screenshots/documentation linked to below)

I have personally been using one of these network appliances (as my only firewall/router) without a problem for the last 3-4 years now. I used to have to reboot my Linksys router every couple of weeks due to it hanging or crashing. When I switching to one of these units I have not once had to reboot (the router). In fact my m0n0wall router hasn't been off since the last time I lost power (several months ago).

These are REALLY SILENT PCs. Except for the power LED, I wouldn't be able to tell when they are on.

These are POWER EFFICIENT PCs. Using a watt-meter, I measured the power at the wall at about 15-20 watts!

These units are complete Single Board Computers, and can be re-configured with several different operating systems including MANY specialized Linux/FreeBSD Distros. You can also download an image of Windows XP Embedded from HP's website (you would need a larger flash disk).




Hardware Specifications:
Processor

800 MHz VIA Eden C3 (x86) processor with PASSIVE HEATSINK (Fanless! Silent PC!)

System Memory

128 MB RAM, (upgradeable to 1 GB through 2x PC133 SDRAM slots)

Network Connectivity

2x (Dual) 10/100 NIC (LAN/WAN), RJ-45

Additional LAN or WIFI ports are available through the PCI slot or USB adapters

Storage

16 MB (or larger) ATA Disk-On-Module flashed with the latest m0n0wall firmware (currently 1.33)

1x 44 pin IDE connector (supports 2 IDE devices, currently housing the ata disk-on-module)

Expansion Slot

1 PCI slot (currently housing the 2nd 10/100 NIC)

I/O Connectors

2x USB 1.1 (add a USB NIC or WIFI adapter)

2x Serial ports (console support)

VGA port (console support)

1 Parallel port

PS/2 Keyboard and Mouse (console support)

Audio connectors

Dimensions

11.375" (W) x 9.0" (D) x 2.125" (H) (About the size of a text-book)

Weight

6 lbs 2.5 oz

Operating System

Pre-loaded with the latest version of the open source m0n0wall project (1.33 or later) (See below for details)

Upgrades (Please contact me first):

• $10 - Upgrade to 256 MB DiskOnModule (I can also pre-install pfSense 1.2.2 embedded instead of m0n0wall)
• $15 - Upgrade to 512 MB DiskOnModule (I can also pre-install pfSense 1.2.3 or 2.0.1 nanobsd instead of m0n0wall)
• $25 - Upgrade to 1 GB DiskOnModule (I can also pre-install pfSense 1.2.3 or 2.0.1 nanobsd instead of m0n0wall)
• $10 - Upgrade from 128 MB RAM to 256 MB RAM
• $15 - Upgrade from 128 MB RAM to 512 MB RAM
• $25 - Upgrade from 128 MB RAM to 1 GB RAM
• $40 - Upgrade to dual 2x Gigabit PCI NIC (3 total RJ-45 ports - WAN/LAN/OPT1)

*** NOTE *** Upgrade quantities may be limited, so make sure and contact me to ensure I have stock on hand. If you do want an upgrade, wait for me to send an invoice showing the total price before sending payment.






m0n0wall (http://m0n0.ch/wall) provides many of the features of expensive commercial firewalls, including:

• web interface (supports SSL)
• serial console interface for recovery
  • set LAN IP address
  • reset password
  • restore factory defaults
  • reboot system
• wireless support (access point with PRISM-II/2.5/3 cards, BSS/IBSS with other cards including Cisco)
• captive portal
• 802.1Q VLAN support
• stateful packet filtering
  • block/pass rules
  • logging
• NAT/PAT (including 1:1)
• DHCP client, PPPoE, PPTP and Telstra BigPond Cable support on the WAN interface
• IPsec VPN tunnels (IKE; with support for hardware crypto cards, mobile clients and certificates)
• PPTP VPN (with RADIUS server support)
• static routes
• DHCP server and relay
• caching DNS forwarder
• DynDNS client and RFC 2136 DNS updater
• SNMP agent
• traffic shaper
• SVG-based traffic grapher
• firmware upgrade through the web browser
• Wake on LAN client
• configuration backup/restore
• host/network aliases

Click Here for screenshots. Click on an image for a larger version Click on an image for a larger version