When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Pulled from a working environment. It's been factory reset and ready to be used.Sold as is. No returns.Default Port ConfigurationPort LabelOS NotationSpeed/TypeManagement Port1p110/100/1000 MBit RJ45X2p210/100/1000MBit RJ453p310/100/1000MBit RJ454p410/100/1000MBit RJ45
The CloudGen Firewall hardware appliances ship with aQuick Start Guide. Follow this guide to connect to your firewall. To protect your network, follow the instructions for the standard deployment.
Hardware SpecificationsInterface
RJ45 Ethernet NICs
4 x 1 GbEUSB 2.04Serial console1 [RJ45]Data StorageRAM [GB]2Mass StorageTypeSSDSize [GB]
- 30 (until 03/2017)
- 50 (since 03/2017)
Size, Weight, DimensionsAppliance weight[kg]1.3Carton weightwith appliance [kg]3.2Appliance size: width x depth x height [mm]274 x 162 x 44Carton size: width x depth x height [mm]650 x 394 x 487Form factorCompact
The hardware specifications list was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological advancements. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks appliance it was delivered with.
Wall Mount Kit
This appliances is shipped with a wall mount kit. Print theBarracuda CloudGen Firewall Wall Mount Jigto use as a template when drilling the required holes. Do not scale the PDF when printing.
LEDs and Acoustic Signals
Your appliance is equipped with a variety of LEDs and acoustic signals. The front panel of theBarracuda CloudGen Firewall F18 contains one power LED (blue), one disc LED (green), one status LED (red), and 4 port LEDs. On the back panel, you can see one power button LED and various port LEDs. Two acoustic signals indicate the status of installation.The tables below show the different meanings of the different glowing states and acoustic signals:
LED ColorStatusMeaning InstallationMeaning Operation
All LEDs Off
Off
Appliance is powered off or installation has not initialized far enough for LED control when installation is started.
Appliance is powered off.
Power LED front side - BLUE
Steady
-
Appliance is plugged in and is on.Status LED front side - REDOffInstallation has finished successfully.Box is running normally.
Status LED front side - RED
Steady
After a hotfix installation, the LED turns to red until the next reboot in case the hotfix installation failed. This feature requires firmware 7.1.3 or higher OR 7.2.2 or higher.
Appliance is halted and may be disconnected, or an error occurred preventing the appliance from entering the up state.Status LED front side - REDBlinking slowly (1/s interval)Normal installation.Appliance is either booting, shutting down, or performing a system update.
Status LED front side - RED
Blinking fast (4/s interval)
Error during installation.
Appliance is inARTmode.
Disc LED - GREEN
Blinking
Appliance is reading or writing on storage.
Appliance is accessing the internal storage.
Port LEDs - GREEN/YELLOW
Left blinking
Data transfer – Yellow (10/100 Mbps)
Port in use.Right steady-Port is on.PSU LEDs - GREENSteady
PSU modules connected and running
Power supply unit is up and running.
Off
Power defective, standby, or shutdown
Power supply unit is off or in standby mode.Acoustic SignalFrequencyMeaningBeep
1 time
(.)
Appliance is booting.Beep
3 times
(...)
Installation was completed successfully; appliance is halted for reboot. After reboot, one beep will again indicate booting.Beep
3 times long
(_ _ _)
Error during installation.
LED and acoustic signals may vary between different appliance models.
Serial Console Port
In order to establish a console connection to the appliance using an RJ45 serial cable, you need to configurethe serial port on the terminal using the following bit1ParityNoneHandshakeNone