CheckPoint L50 Network Security Appliance Firewall Boot Screen in the Ad For Sale

Ifthe item is going to be shipped please read the shipping message at the end ofthis listing.

This sale is for a

Includes the CheckPoint L50 as seen in the pictures and a 12 volt power supply.

I received a small lot of Check Point devices. This one appear to be new without the box.

I do not know if any license, activation orregistration is required to use this unit. I do not have any information on theprevious owner of this device and cannot help you in regards to anyregistration or support. Check with CHECK POINT directly for any questionsabout this device.

You will probably have to purchase a license for continued use.

See the Boot Screen at the end of the Ad.

It powers on and produces the Console screen in Hyper terminal listed below.

See theConsolescreen from Hyper terminal at the end of the ad.

We are not in theNetwork Equipment Business.

Sometimes other equipment is included in lots we buy

Most of the time we are only able to perform basic test (power up/ self test)

The item is in good cosmetic condition.

The sale is for the items listed only.

NO other cords, cable\'s software, manuals licenses or passwords.

The item is sold with a DOA warranty. The item will havewarranty void if removed labelson the major components.

DO notremove the warranty void if removed labels until you are satisfied with the item.

Please notify me of any problems within 3 days after receiving the item.

You caninspect this item or the winning buyer can pick them upSaturdays and Sundays 11: AM to 4: PM at the used computer booth at Englishtown sale Sales in Englishtown, NJ

its booth 69 in the blue building.
Use the ask the seller a question feature if you want to inspect the item.
Be sure I know you are coming so I can make sure the item is there not in storage.
For directions to Englishtown sale click on the directions link on the Englishtown sale web page.

BOOT SCREEN FOLLOWS

______ __ __ _______ _ _
.\' ___ |[ | [ | _ |_ __ \\ (_) / |_
/ .\' \\_| | |--. .---. .---. | | / ] | |__) | .--. __ _ .--. `| |-\'
| | | .-. |/ /__\\\\/ /\'`\\] | \'\' < | ___// .\'`\\ \\[ | [ `.-. | | |
\\ `.___.\'\\ | | | || \\__.,| \\__. | |`\\ \\ _| |_ | \\__. | | | | | | | | |,
`.____ .\'[___]|__]\'.__.\'\'.___.\'[__| \\_] |_____| \'.__.\' [___][___||__]\\__/** MARVELL BOARD: RD-88F6281A LEU-Boot 1.1.4 (Aug 11 2010 - 13:38:30) Check Point version: 3.4.27U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CFB00Soc: 88F6281 A1 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200MhzDRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM Total size 256MB 16bit width************ Hit \'Ctrl + C\' for boot menu ************Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash: 0 kBCPU : Marvell Feroceon (Rev 1)Streaming disabled
Write allocate disabledModule 0 is RGMII
Module 1 is TDMUSB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0, egiga1 [PRIME]Reading data from 0xe0000 -- 100% complete.
Verifying CRC for settings area... DoneUSB: scanning bus for devices... 2 USB Device(s) found
0 Storage Device(s) found
NAND read: device 0 offset 0x100000, size 0x800000Reading data from 0x8ff800 -- 100% complete.
8388608 bytes read: OK
Saving Environment to NAND...
Erasing Nand...Writing to Nand... done
## Booting image at 02000200 ...
Image Name: Linux-2.6.22.18
Created: 2010-08-10 14:56:52 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 5999020 Bytes = 5.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OKStarting kernel ...Uncompressing done, booting the kernel.
INIT: version 2.86 bootingBooting Check Point RD-6281-A User Space...
INIT: Entering runlevel: Started...Gateway-ID-7F216018 login:
Gateway-ID-7F216018 login:
Gateway-ID-7F216018 login:
Gateway-ID-7F216018 login: