When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Dynex DE-5020 exerciser
I have the manual for the Dynex 6000 series disk drive that I can share with you which includes the operating instructions for the DE-5020 exerciser.I haven't been able to find much information about this, but I did find a small email thread about it, which I share below:
I've recently come across a device that looks like it is some kind ofdisk drive test exerciser made by Western Dynex.
It's a small box with toggle switches in two groups. One group has nineswitches labeled in powers of two from 1 to 256. The other group hasfive switches that appear to be two-way momentary contact (up|down) thatare labeled BUSY +|BUSY -; DEC/HEAD 1|INC/HEAD 0; INITIAL/BOTDISK|REPET/TOP DISK; RECYCLE|LOAD REGISTER; LOAD COMMAND|CLEARThere are no indicator lamps on the device, just the switches.
It has a ribbon cable that comes out of it that terminates in apaddle-type board that looks suspiciously like the paddle board thatwould plug into the drive electronics backplane of a DEC RK05 diskdrive.
I checked BitSavers, and there's no documents for Dynex or WesternDynex. I did a little searching, and it looks like Western Dynex made(or OEM'd) disk drives that were similar to the Diablo 30 drives, whichwere the basis of the DEC RK05.
So, here's the questions: Does anyone know of this particular testerdevice, and can it be used to exercise RK05's. Anyone have anydocumentation that might explain how the thing is operated?
***
> It's a small box with toggle switches in two groups. One group has nine> switches labeled in powers of two from 1 to 256. The other group has> five switches that appear to be two-way momentary contact (up|down) that> are labeled BUSY +|BUSY -; DEC/HEAD 1|INC/HEAD 0; INITIAL/BOT> DISK|REPET/TOP DISK; RECYCLE|LOAD REGISTER; LOAD COMMAND|CLEAR
'BOT DISK' / 'TOP DISK' suggests it might be an exerciser for one ofthose drives with 2 platters, one fixed and the other removable. I usedone years ago that was badged (and maybe made) by Plessey, it linked toa normal RK11-D controller and appeared as a pair of RK05s.
> There are no indicator lamps on the device, just the switches.
What's inside it? Does it look to be simple (a few SSI TTL chips) orcomplicated (lots of TTL, or a microprocessor)?
>> It has a ribbon cable that comes out of it that terminates in a> paddle-type board that looks suspiciously like the paddle board that> would plug into the drive electronics backplane of a DEC RK05 disk> drive.>> I checked BitSavers, and there's no documents for Dynex or Western> Dynex. I did a little searching, and it looks like Western Dynex made> (or OEM'd) disk drives that were similar to the Diablo 30 drives, which> were the basis of the DEC RK05.
Err no. The Riablo 30 is the RK02 (low density) or RK03 (high density).The RK05 might look the same to software (although there are differencesin the interface, particularly the drive select lines [1]), but internallyit's quite different (the Dioblo 30 uses a permanent magnet DC motor as thehead positioner, I am not joking, the thing's got brushes and a commutator!)
[1] The Diablo 30 has 4 1-of-n select lines. The RK05 can be configured(by a pin o nthe itnerface connector) to either do that, or to have 3binary-coded select lines. The RK11-C controller does 1-of-4 select, andcan have up to 4 drives (RK05s or Diablo 30s) on each of 2 cables. TheRK11-D uses binary select lines and can have 8 RK05s ona single cable.IIRC that Plessey drive I mentioned had a little PCB that plugged intothe RK11-D drive connector containing a decoder chip to turn the 3-bitbunarly select into 1-of-n select.
My guess is that this is some kind of drive exerciser, possibly to dorepeating seek patterns (like the ones mentioned in the RK05 maintenancemanual) that you use when settign up the postiioner waveforms. But Idon't have the docs.
